Chimney Pipe Accessories

View as Grid List
Sort by
Display per page

AmeriVent 6HS-RSA12 Roof Support Box, Black

For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor.
$119.99

AmeriVent 6HS-TWK Through-The-Wall Kit, For: Venting Appliances through a Side Wall

Designed for venting appliances through a side wall. Complete wall support components. Provides all-weather protection.
$629.99

AmeriVent 8HS-CSA Ceiling Support Assembly, Steel, Black

A ceiling support assembly is used when a chimney is installed in a flat ceiling. Available in a black finish, the 6 and 8 in sizes fit between regular 16 in O.C ceiling joists and are cartoned with a stainless steel black single wall adapter.
$99.99

AmeriVent 8RSC Adjustable Round Storm Collar, Steel, For: Type B Gas Vent Pipe

Use with HS chimney roof flashing to insure water tight installation.
$7.99

FMI CP-8DM Chimney Vent Kit, For: 8 in ID, 12-3/8 in OD, 1700 deg pipe

Roof flashing with 24 in base, firestop spacer, round termination cap, storm collar and flue extension. Fits standard 8 in ID, 12-3/8 in OD, 1700 deg pipe.
$179.99

SELKIRK 200250 Universal Roof Support Assembly, Stainless Steel, Galvanized, For: 5 to 8 in Dia Chimney Pipe

This new design gives you the flexibility of securing the 5, 6, 7 or 8 in Dia chimney with a heavy-duty band. The band allows you to slide the installed length verticaly to properly position this section in the system. Installation requirements are the same as our standard RSP. The URSA can hold 30 ft of pipe total only 20 ft.
$57.99

SELKIRK 200420 Roof Support Kit, Universal, Stainless Steel, For: All Roof Pitches and Requires Only Simple Framing

Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only.
$59.99

SELKIRK 206400 Anchor Plate, Stainless Steel

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection.
$47.99

SELKIRK 206430 Wall Support Kit, Type HT, Stainless Steel, Galvanized

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5, 6, 7 and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of the larger sizes, 10, 12 and 14 in, is 40 ft of chimney. The wall support is intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection.
$62.99

SELKIRK 206440 Roof Brace Kit, Stainless Steel

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4 to 6 ft.
$79.99

SELKIRK 206480 Round Finishing Collar, Black, Matte

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
$16.99

SELKIRK 206488 Trim Plate Spacer, Steel, Black, Matte

Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield.
$31.99

SELKIRK 206620 Ceiling Support Kit, Flat, Stainless Steel, For: Model SSII

Provides the support package and termination parts for a chimney that is supported by a flat ceiling and passes through an attic area and penetrates a 2/12 to 6/12 pitch roof. Just add pipe lengths and the Flat Ceiling Support Kit (FCK) has all necessary parts for complete installation. However, depending upon your roof design and the position of your chimney on the roof, it may be necessary to install a roof brace kit to provide required support for your chimney above the roof.
$299.99

SELKIRK 206621 Ceiling Support Kit, Pitched, Stainless Steel, For: Model SSII

The Pitched Ceiling Support Kit provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and adjustable flashing (AF). Selection of the Adjustable Flashing is determined by the pitch of your roof.
$269.99

SELKIRK 206622 Thru-the-Wall Support Kit, Stainless Steel, For: Model SSII

For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running verticaly up the exterior wall to termination above the roof line. The thru-the-wall support kit provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height.
$449.99

SELKIRK 206791 Spark Arrestor, Stainless Steel

Diamond shaped 1/2 in x 1 in mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.
$18.99

SELKIRK 206800 Chimney Topper, Stainless Steel

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Sure-Temp-Type HT Chimney (5 in, 6 in, 7 in and 8 in sizes) the round top is designed with three legs that slide down over the outside of the chimney. A cinch band is then positioned over the legs and tightened to hold the top firmly in place. This design makes cap removal for cleaning a breeze.
$64.99

SELKIRK 206810 Storm Collar, For: Round Chimney Pipe

Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning.
$11.99

SELKIRK 208400 Anchor Plate, Stainless Steel

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection.
$64.99

SELKIRK 208430 Wall Support Kit, Type HT, Stainless Steel, Galvanized

The Type HT wall support kit has been tested for use fully enclosed and has been designed in 5, 6, 7 and 8 in sizes to carry up to 60 ft of height at 2 in from wall. The capacity of the larger sizes, 10, 12 and 14 in, is 40 ft of chimney. The wall support is intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection.
$77.99

SELKIRK 208440 Roof Brace Kit, Stainless Steel

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4 to 6 ft.
$84.99

SELKIRK 208480 Round Finishing Collar, Black, Matte

Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
$19.99

SELKIRK 208488 Trim Plate Spacer, Steel, Black, Matte

Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield.
$45.99

SELKIRK 208621 Ceiling Support Kit, Pitched, Stainless Steel

The Pitched Ceiling Support Kit provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and adjustable flashing (AF). Selection of the Adjustable Flashing is determined by the pitch of your roof.
$299.99

SELKIRK 208791/208790 Spark Arrestor, Stainless Steel

Diamond shaped 1/2 in x 1 in mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.
$22.99

SELKIRK 208800 Chimney Topper, Stainless Steel

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Sure-Temp-Type HT Chimney (5 in, 6 in, 7 in and 8 in sizes) the round top is designed with three legs that slide down over the outside of the chimney. A cinch band is then positioned over the legs and tightened to hold the top firmly in place. This design makes cap removal for cleaning a breeze.
$87.99

SELKIRK SuperVent 2100 Series JM6FP Finishing Plate, Stainless Steel, 1, Pack

SELKIRK SuperVent 2100 Series Finishing Plate, Specifications: 6 in Size, Stainless Steel, 10 in Dia x 16 in W Dimensions, Pack, 1
$12.99

SELKIRK SuperVent 2100 Series JM6P2 Peak Flashing, Galvalume Steel, 1, Pack

SELKIRK SuperVent 2100 Series Peak Flashing, Specifications: 6 in Size, Galvalume Steel, 14 x 12-1/2 x 24 in Dimensions, Pack, 1, Includes: Storm Collar
$12.99

SELKIRK SURE-TEMP 206600 Roof Termination Kit, Type HT, Steel

Three basic chimney kit is designed around one of the standard support systems.
$139.99

SHELTER SCLK Chimney Leg Kit, Heavy-Duty, Stainless Steel

Stainless steel leg kit converts bolt-on style chimney cap to slip-in. For use where tile liner does not protrude.
$7.99
;